CONTRACT FOR THE SUPPLY AND INSTALLATION OF EQUIPMENT FOR THE CHARACTERISATION OF MAGNETORESISTIVE DEVICES FOR THE SPINTRONICS GROUP OF THE INTERNATIONAL IBERIAN NANOTECHNOLOGY LABORATORY

INL, International Iberian Nanotechnology Laboratory

THE SUBJECT MATTER OF THIS CONTRACT IS THE SUPPLY AND INSTALLATION OF EQUIPMENT FOR THE CHARACTERISATION OF MAGNETORESISTIVE DEVICES FOR THE SPINTRONICS GROUP OF THE INTERNATIONAL IBERIAN NANOTECHNOLOGY LABORATORY
The tender consists of four lots as follows:
Lot 1: 20 GHz Real Time Oscilloscope
Lot 2: Electromagnet System
Lot 3: Vibration Isolation Breadboard Table
Lot 4: Magnetic Noise Isolation Chamber

Prazo de entrega

O prazo para a recepção das propostas era 2013-07-31. O concurso foi publicado em 2013-07-01.

Fornecedores

Os seguintes fornecedores são mencionados nas decisões de adjudicação ou noutros documentos de contratação:

Quem?

• INL, International Iberian Nanotechnology Laboratory

O quê?

Onde?

• Norte › Cávado

Histórico de aquisições

Data	Documento
2013-07-01	Anúncio de concurso
2013-10-24	Anúncio de adjudicação

Anúncio de concurso (2013-07-01)
Objecto
Âmbito do concurso
Título: Equipamento laboratorial, óptico e de precisão (exc. óculos)
Quantidade ou extensão:

Lot 1: 20 GHz Real Time Oscilloscope - One UnitLot 2: Electromagnet System - One UnitLot 3: Vibration Isolation Breadboard Table - One UnitLot 4: Magnetic Noise Isolation Chamber - One Unit146 000

Valor total do procedimento: 87 000 💰
Metadados do anúncio
Idioma original: inglês 🗣️
Tipo de documento: Anúncio de concurso
Natureza do contrato: Fornecimentos
Regulamento: União Europeia
Vocabulário comum para os contratos públicos (CPV)
Código: Equipamento laboratorial, óptico e de precisão (exc. óculos) 📦

Procedimento
Tipo de procedimento: Concurso público
Tipo de proposta: Apresentação de uma proposta relativa a um ou mais lotes
Critérios de atribuição
Proposta economicamente mais vantajosa

Entidade adjudicante
Identidade
País: Portugal 🇵🇹
Tipo de autoridade adjudicante: Instituição Europeia/Agência ou organização internacional
Nome da autoridade adjudicante: INL, International Iberian Nanotechnology Laboratory
Endereço postal: Avenida Mestre José Veiga
Código postal: 4715 330
Cidade postal: Braga
Contacto
Endereço Internet: http://www.inl.int 🌏
Correio electrónico: adrian.watson@inl.int 📧
Telefone: +351 253140112 📞
Fax: +351 253140119 📠

Referência
Datas
Data de envio: 2013-07-01 📅
Prazo de apresentação: 2013-07-31 📅
Data de publicação: 2013-07-05 📅
Identificadores
Número do anúncio: 2013/S 129-221632
Número JO-S: 129

Objecto
Âmbito do concurso
Breve descrição:

The tender consists of four lots as follows:

Lot 1: 20 GHz Real Time Oscilloscope

Lot 2: Electromagnet System

Lot 3: Vibration Isolation Breadboard Table

Lot 4: Magnetic Noise Isolation Chamber

Número do lote: 1
Designação do lote: Lot 1 - 20 GHz Real Time Oscilloscope
Breve descrição:

- 20 GHz bandwidth- 4 channels- Sample rate of 40Gsample/channel using 4 channels- Voltage noise floor of 0.5 mV rms in a scale of 10mV/div- Voltage range adjustable between 10mV/div and 1V/div- Jitter noise floor of 100 fs- Time scale adjustable between 2ps/div and 20s/div- Memory depth of 1Gpoints on 4 channels- Adapters required to connect SMA terminated cables to the inputs must be supplied- GPIB interface- Rack mount kit- Enclosure with safety lock-out

- 20 GHz bandwidth

- 4 channels

- Sample rate of 40Gsample/channel using 4 channels

- Voltage noise floor of 0.5 mV rms in a scale of 10mV/div

- Voltage range adjustable between 10mV/div and 1V/div

- Jitter noise floor of 100 fs

- Time scale adjustable between 2ps/div and 20s/div

- Memory depth of 1Gpoints on 4 channels

- Adapters required to connect SMA terminated cables to the inputs must be supplied

- GPIB interface

- Rack mount kit

- Enclosure with safety lock-out

Quantidade ou extensão: One Unit
Número do lote: 2
Designação do lote: Lot 2 - Electromagnet System
Breve descrição:

- Dipole electromagnet with 100mm pole diameter able to reach a field of at least 1.5T at a pole gap of…

… 20mm- 45 degree mounting frame, to allow vertical and horizontal access to the pole gap- Coil power supply with a maximum current noise level of +/-0.04%- The system must be able to monitor the field generated in the gap up to a magnitude of at least 2T.- The system must have a feed-back mechanism to ensure that the field readings in the gap match the set points provided by the user.- The system must be able to sweep the field magnitude and reverse the field direction automatically.- The system must include a control computer that can be used to set and monitor the fields being applied in the gap- The system must include a GPIB interface and must be able to be controlled via GPIB- All the required electronics must supplied within an electronics rack- All interlocks required for the safe operation of the system must be included (thermal interlocks, water flow interlocks, etc…)- The magnet must be compatible with a future upgrade allowing the magnet field direction to rotate vertically, around a horizontal axis.- The magnet footprint should be smaller than 70cm in any of the horizontal directions.- The magnet base must be prepared to be fixed into a breadboard table with 1/4-20 holes.

… 20mm

- 45 degree mounting frame, to allow vertical and horizontal access to the pole gap

- Coil power supply with a maximum current noise level of +/-0.04%

- The system must be able to monitor the field generated in the gap up to a magnitude of at least 2T.

- The system must have a feed-back mechanism to ensure that the field readings in the gap match the set points provided by the user.

- The system must be able to sweep the field magnitude and reverse the field direction automatically.

- The system must include a control computer that can be used to set and monitor the fields being applied in the gap

- The system must include a GPIB interface and must be able to be controlled via GPIB

- All the required electronics must supplied within an electronics rack

- All interlocks required for the safe operation of the system must be included (thermal interlocks, water flow interlocks, etc…)

- The magnet must be compatible with a future upgrade allowing the magnet field direction to rotate vertically, around a horizontal axis.

- The magnet footprint should be smaller than 70cm in any of the horizontal directions.

- The magnet base must be prepared to be fixed into a breadboard table with 1/4-20 holes.

Número do lote: 3
Designação do lote: Lot 3 - Vibration Isolation Breadboard Table
Breve descrição:

- The table top must have a surface with an area of 0.9 x 1.2…

… m2.- The table must be able to hold a weight of 500kg- The surface of the table must have a regular pattern of drilled holes. The holes must be located with a periodicity of 1hole/inch in the XX and YY directions.- The drilled holes must have a thread of type 1/4-20.- The table top must be supplied together with the support posts required to provide the best possible vibration isolation. The isolation efficiency at 10Hz should be at least 90% both for vertical and horizontal vibrations.

… m2.

- The table must be able to hold a weight of 500kg

- The surface of the table must have a regular pattern of drilled holes. The holes must be located with a periodicity of 1hole/inch in the XX and YY directions.

- The drilled holes must have a thread of type 1/4-20.

- The table top must be supplied together with the support posts required to provide the best possible vibration isolation. The isolation efficiency at 10Hz should be at least 90% both for vertical and horizontal vibrations.

Número do lote: 4
Designação do lote: Lot 4 - Magnetic Noise Isolation Chamber
Breve descrição:

- The external magnetic noise in the frequency range from DC-100Hz should be attenuated typically by a factor of 50000 or…

… larger.- The device should isolate a volume able to fit a cylinder with a diameter of 10cm and a length of 20cm.- The device should be closed, isolating the device under test from fields coming from any direction.- A feed-trough socket with an electrically insulated SMA-SMA or BNC-BNC connector is desirable, but not mandatory.

… larger.

- The device should isolate a volume able to fit a cylinder with a diameter of 10cm and a length of 20cm.

- The device should be closed, isolating the device under test from fields coming from any direction.

- A feed-trough socket with an electrically insulated SMA-SMA or BNC-BNC connector is desirable, but not mandatory.

Quantidade ou extensão:

Lot 1: 20 GHz Real Time Oscilloscope - One Unit

Lot 2: Electromagnet System - One Unit

Lot 3: Vibration Isolation Breadboard Table - One Unit

Lot 4: Magnetic Noise Isolation Chamber - One Unit

Número de referência: Aw/rf
Nome do projeto ou programa financiado pela UE:

THIS PROJECT WILL BE CO-FINANCED BY THE EUROPEAN REGIONAL DEVELOPMENT FUND (ERDF), NAMELY THROUGH THE PROGRAMA OPERACIONAL REGIONAL DO NORTE ON.2 (Portugal)

Local de actuação
Local principal ou local de actuação:

Avenida Mestre José Veiga

Braga 4715-330

Portuga

Informações jurídicas, económicas, financeiras e técnicas
Execução do contrato
Depósitos e garantias exigidos:

Bank Guarantee 10% of Contract Value for Duration of the Warranty Period for contracts of value equal to or greater than EUR18,000.00

Procedimento
Línguas
Língua: inglês 🗣️

Entidade adjudicante
Contacto
Ponto de contacto: http://inl.int/contractors_projects?section=contract-opportunities
Adrian Watson
Endereço Internet: www.inl.int 🌏
Endereço do perfil de comprador: http://inl.int/contractors/info 🌏
URL dos documentos: http://inl.int/contractors_projects?section=contract-opportunities 🌏

Referência
Identificadores
Número de referência atribuído pela autoridade adjudicante: Aw/rf
Fonte: OJS 2013/S 129-221632 (2013-07-01)

Anúncio de adjudicação (2013-10-24)
Objecto
Âmbito do concurso
Valor total do procedimento: 99 339 💰
Metadados do anúncio
Tipo de documento: Anúncio de adjudicação

Procedimento
Tipo de proposta: Não consta

Referência
Datas
Data de envio: 2013-10-24 📅
Data de publicação: 2013-10-26 📅
Identificadores
Número do anúncio: 2013/S 209-362086
Refere-se ao anúncio: 2013/S 129-221632
Número JO-S: 209
Informações adicionais

Lot 2 is not awarded as neither offer received was deemed acceptable. The first offer was at a higher price than the maximum allowed and the second tenderer failed to provide adequate technical information.

Procedimento
Critérios de atribuição
Critério: 1. Technical Quality (20)
2. Price (15)
3. Delivery Schedule (15)
4. Payment Terms (10)
5. Warranty (10)
6. Technical Assistance (5)
7. Installation and Training (5)
8. List of References (5)
9. Improvements (5)

Adjudicação do contrato

1️⃣
Data de celebração do contrato: 2013-10-15 📅
Nome: eNGN Technologies – Soluções de Medida e Telecomunicações, Lda.
Endereço postal: Taguspark Núcleo Central 150
Cidade postal: Porto Salvo
Código postal: 2740-122
País: Portugal 🇵🇹
Correio electrónico: engn@engn.pt 📧
Endereço Internet: www.engn.p 🌏

2️⃣
Nome: M.T. Brandão, Lda.
Endereço postal: Rua de Serralves, 599
Cidade postal: Porto
Código postal: 4150-708
Correio electrónico: web@mtbrandao.com 📧
Endereço Internet: http://www.mtbrandao.com/ 🌏

3️⃣
Nome: Sekels GmbH
Endereço postal: Dieselstrasse 6
Cidade postal: Ober-Moerlen
Código postal: 61239
País: Alemanha 🇩🇪
Correio electrónico: mail@sekels.com 📧
Endereço Internet: http://www.sekels.com/ 🌏
Informações sobre concursos
Número de propostas recebidas: 2
1
Fonte: OJS 2013/S 209-362086 (2013-10-24)

Novas aquisições em categorias conexas 🆕

Equipamento laboratorial, óptico e de precisão (exc. óculos) (15 novas aquisições)